Top 8 Rotary Encoder Arduino – Single Board Computers

As an Amazon Associate I earn from qualifying purchases.



DEVMO 2PCS KY-040 Rotary Encoder Module Brick Sensor Development Board Compatible with Arduino Raspberry Pi SMT32 Development Board

DEVMO #ad - Model: ky-040 Working voltage: 5V. The rotary encoder is used to measure the speed and with PWM technology, Can achieve rapid speed devices with fixed bolt hole for easy installation. Package includes: 2pcs Rotary Encode. Size: 32 x 19 x 30mm.
BrandDEVMO #ad
ManufacturerDEVMO #ad

2. SparkFun


SparkFun Qwiic Twist, RGB Rotary Encoder Breakout-Small easy to use breakout Qwiic system for no soldering connection 6mm shaft for knob of choice Red Green Blue LEDs mix for 16 million color options

SparkFun #ad - Voltage: 3. 3v. Length/width: 1" x 1. 2" 25. 4mm x 305mm. Heads up! the qwiic twist is designed to operate at 3. 3v so please don’t drive it at 5V.

Clockwise and counterclockwise direction is detected. Approximately 406ma with leds on 100%. 2x qwiic Connectors. Jumpers for address selection, interrupt pull up disable, Default, and I2C pull up disable. Up to 400khz I2C communication. Built-in momentary button. Rgb led controlled via PWM allowing for up to 16M colors. Your i2c pins, however, can be 5V logic. Software configurable i2c address - up to 111 devices on a single bus. I2c address: 0x3f jumper Open, 0x3E Jumper Closed. Current: approximately 2. 8ma leDs off. 24 ticks per 360° rotation. Height: 0984" 25mm.
BrandSparkFun #ad
ManufacturerSparkFun Electronics #ad
Height1.38 Inches
Length1.38 Inches
Weight0.02 Pounds
Width1.18 Inches
Part NumberSEN-15177

3. waveshare


Waveshare Rotary Encoder Angle Module Sensor Development Kit MEGA UNO 360 Degree Rotation

waveshare #ad - In the case of working with a mcu: vcc ↔ 3. 0v ~ 5. 3v gnd ↔ power supply ground sw ↔ mcu. Io encoder button status SIB ↔ MCU. Io output status SIA ↔ MCU. Io output status. Pulses per lap: 15 power: 3. 0v ~ 5. 3v. Dimension: 32. 1mm * 15. 4mm mounting holes size: 2. 0mm. Positioning in Industrial Controls. Detects clockwise/anti-clockwise rotations: degrees and laps.
Brandwaveshare #ad
ManufacturerWaveshare #ad
Height3.54 Inches
Length7.09 Inches
Weight0.02 Pounds
Width3.94 Inches
Part NumberRotation Sensor
ModelRotation Sensor

4. Gump's grocery


Gump's grocery 2Pcs Rotary Encoder Module Brick Sensor Development Board for Arduino

Gump's grocery #ad - Working voltage: 5V. Pulse circle: 20 Main color: Black. Size: about 31 * 19 * 29mm / 1. 22" * 075" * 1. 14". Material: electronic components + PCB.
BrandGump's grocery #ad
ManufacturerGump's grocery #ad
Part NumberTG106

5. daier


Daier KY-040 Rotary Decoder Encoder Module for Arduino AVR PIC

daier #ad - The rotary encoder is used to measure the speed and with PWM technology can achieve rapid speed devices With fixed bolt hole for easy installation. Great for DIY project Specification.
Branddaier #ad
Manufacturerdaier #ad
Part NumberE575

6. 221 Robotic Systems


221 Robotic Systems Lamprey Absolute Rotary Encoder-Hollow Bore, Analog/UART/PWM, 10-bit

221 Robotic Systems #ad - 10-bit analog, 10-bit pwm1000us-2000us, 3. 3v or 5v, uART5v. The sensor comes in kit form and includes the sensor board, magnet and 10-pin cable. Glue it to any rotating surface or 3D print a custom hub. The supplied magnet target has an ID of 1. 23" and is designed to pilot on the flange of a standard 1/2" bearing. Custom large bore magnet target, Wide axial sensing range. 015"-05".
Brand221 Robotic Systems #ad
ManufacturerTeam 221 LLC #ad
Part NumberLP-001-1

7. WayinTop


WayinTop 3PCS 0.91 inch OLED Display Module IIC SSD1306 128x32 OLED Screen Driver DC 3.3V~5V for Arduino ESP32 ESP8266 AVR PIC STM32 Raspberry pi Blue

WayinTop #ad - High performancethe display performance is better than the traditional LCD display, and runs on the SSD1306 display driver, it uses the very common I2C bus, also lower consumption; IIC I2C communications simplifies connections. High resolution high resolution oled for any of your micro controller projects, 128x32 pixels gives you a nice sharp, crisp text output. Specificationoled display, no need backlight, self-illumination, 3.3v-5v power; resolution: 128 x 32. Widely applicationit's great for such as pic, avr, ardUINO ESP32 ESP8266, ARM and Raspberry Pi. Etc.
BrandWayinTop #ad
ManufacturerWayinTop #ad
Height0.2 Inches
Length3.94 Inches
Width3.94 Inches
Part NumberFC#WYTP61-BL-3



ELEGOO Upgraded 37 in 1 Sensor Modules Kit with Tutorial Compatible with Arduino IDE UNO R3 MEGA2560 Nano

ELEGOO #ad - Updated from the old version others: Received great ideas from our customers and adopted in this upgraded kit. Upgraded tutorial only for r3, listing paper, nano in cd, mega2560 r3, resistors pack only from Elegoo Team.

Note: to use elegoo starter kits requires basic electronic knowledge. If the user has no experience, it would be better to have someone lead and teach them while studying. If you prefer download the tutorials online from the official website. 100% compatible with arduino official IDE, Raspberry Pi and STM32. There are tutorials in the CD that comes with. Removed useless modules like light cup and mercury module, two of the hall sensors, LCD1602 screen, one of the dual-color sensor. Add useful modules like gy-521 accelerometer module, heartbeat sensor, DS1307 real time clock module etc.
BrandELEGOO #ad
ManufacturerELEGOO #ad
Height1.73 Inches
Length10.63 Inches
Width7.09 Inches
Part NumberEL-KIT-011
Warrantyhalf year